Capacitively Coupled Plasma from Laser-Induced Graphene Points to Ozone as the Major Mediator of Antibacterial Activity.

Low-temperature plasma is an emerging approach for the treatment of bacterial infections. Nonchemical treatments such as cold plasma offer potential solutions to antibiotic resistance. We investigated the use of laser-induced graphene as an inexpensive, lightweight, and portable electrode for generating cold plasma. At the same time, the mechanism or molecular mediators of cold plasma-induced antibacterial activity remain poorly understood. This study validates graphene as an efficient structure for producing therapeutic cold plasma, and this study also indicates that ozone is the primary mediator of antibacterial activity in graphene-mediated cold plasmas for bacterial growth under the conditions studied.

Robust Superhydrophobic Surfaces via the Sand-In Method.

Superhydrophobic surfaces have gained sustained attention because of their extensive applications in the fields of self-cleaning, anti-icing, and drag reduction systems. Water droplets must have large apparent contact angle (CA) (>150°) and small CA hysteresis (<10°) on these surfaces. However, previous research usually involves complex fabrication strategies to modify the surface wettability. It is also challenging to maintain the temporal and mechanical stability of the delicate surface textures. Here, we develop a one-step solvent-free sand-in method to fabricate robust superhydrophobic surfaces directly atop various substrates with an apparent CA up to ∼163.8° and hysteresis less than 5°. The water repellency can withstand 100 Scotch tape peeling tests and remain stable after being stored under ambient humid conditions in Houston, Texas, for 18 months or being heated at 130 °C in air for 24 h. The superhydrophobic surfaces have excellent anti-icing ability, including a ∼2.6× longer water freezing time and ∼40% smaller ice adhesion strength with the temperature as low as -35 °C. Since the surface layers are fabricated by sanding the substrates with the powder additives, the surface damage can be repaired by a direct re-sanding treatment with the same powder additives. Further sand-in condition screenings broaden surface wettability from hydrophilic to superhydrophobic. The sand-in method induces the surface modification and the formation of the tribofilm. Surface and materials characterizations reveal that both microstructures and nanoscale asperities of the tribofilms contribute to the robust superhydrophobic features of sanded surfaces.

High-Resolution Laser-Induced Graphene from Photoresist.

The fabrication of patterned graphene electronics at high resolution is an important challenge for many applications in microelectronics. Here, we demonstrate the conversion of positive photoresist (PR), commonly employed in the commercial manufacture of consumer electronics, into laser-induced graphene (LIG). Sequential lasing converts the PR photopolymer first into amorphous carbon, then to photoresist-derived LIG (PR-LIG). The resulting material possesses good conductivity and is easily doped with metal or other additives for additional functionality. Furthermore, photolithographic exposure of PR prior to lasing enables the generation of PR-LIG patterns small enough to be invisible to the naked eye. By exploiting PR as a photopatternable LIG precursor, PR-LIG can be synthesized with a spatial resolution of ∼10 µm, up to 15 times smaller than conventional LIG patterning methods. The patterning of these small PR-LIG features could offer a powerful and broadly accessible strategy for the fabrication of microscale LIG-derived nanocomposites for on-chip devices.

Laser-Induced Graphene Triboelectric Nanogenerators.

Triboelectric nanogenerators (TENGs) show exceptional promise for converting wasted mechanical energy into electrical energy. This study investigates the use of laser-induced graphene (LIG) composites as an exciting class of triboelectric materials in TENGs. Infrared laser irradiation is used to convert the surfaces of the two carbon sources, polyimide (PI) and cork, into LIG. This gives the bilayer composite films the high conductivity associated with LIG and the triboelectric properties of the carbon source. A LIG/PI composite is used to fabricate TENGs based on conductor-to-dielectric and metal-free dielectric-to-dielectric device geometries with open-circuit voltages >3.5 kV and peak power >8 mW. Additionally, a single sheet of PI is converted to a metal-free foldable TENG. The LIG is also embedded within a PDMS matrix to form a single-electrode LIG/PDMS composite TENG. This single-electrode TENG is highly flexible and stretchable and was used to generate power from mechanical contact with skin. The LIG composites present a class of triboelectric materials that can be made from naturally occurring and synthetic carbon sources.

Laser-Induced Graphene for Flexible and Embeddable Gas Sensors.

Laser-induced graphene (LIG) has received much attention since it enables simple and rapid synthesis of porous graphene. This work presents a robust direct-write LIG-based gas sensor, which senses gases based on thermal conductivity, similar to a katharometer sensor. The gas sensors are fabricated by lasing polyimide substrates with a 10.6 µm CO2 laser to synthesize LIG. This enables the formation of flexible gas sensors which could be incorporated on a variety of surfaces. High surface area and thermal conductivity of the LIG results in rapid response times for all studied gases. The gas sensors are also embedded in cement to form a refractory composite material. These sensors are used to determine composition of various gas mixtures, such as N2 and CO2, which are the most abundant gaseous species in flue gas. Thus, LIG based embeddable sensors could be incorporated in composites to enable electronically functional construction materials.

Laser-Induced Graphene by Multiple Lasing: Toward Electronics on Cloth, Paper, and Food.

A simple and facile method for obtaining patterned graphene under ambient conditions on the surface of diverse materials ranging from renewable precursors such as food, cloth, paper, and cardboard to high-performance polymers like Kevlar or even on natural coal would be highly desirable. Here, we report a method of using multiple pulsed-laser scribing to convert a wide range of substrates into laser-induced graphene (LIG). With the increased versatility of the multiple lase process, highly conductive patterns can be achieved on the surface of a diverse number of substrates in ambient atmosphere. The use of a defocus method results in multiple lases in a single pass of the laser, further simplifying the procedure. This method can be implemented without increasing processing times when compared with laser induction of graphene on polyimide (Kapton) substrates as previously reported. In fact, any carbon precursor that can be converted into amorphous carbon can be converted into graphene using this multiple lase method. This may be a generally applicable technique for forming graphene on diverse substrates in applications such as flexible or even biodegradable and edible electronics.

Laser-Induced Graphene Formation on Wood.

Wood as a renewable naturally occurring resource has been the focus of much research and commercial interests in applications ranging from building construction to chemicals production. Here, a facile approach is reported to transform wood into hierarchical porous graphene using CO2 laser scribing. Studies reveal that the crosslinked lignocellulose structure inherent in wood with higher lignin content is more favorable for the generation of high-quality graphene than wood with lower lignin content. Because of its high electrical conductivity (≈10 Ω per square), graphene patterned on wood surfaces can be readily fabricated into various high-performance devices, such as hydrogen evolution and oxygen evolution electrodes for overall water splitting with high reaction rates at low overpotentials, and supercapacitors for energy storage with high capacitance. The versatility of this technique in formation of multifunctional wood hybrids can inspire both research and industrial interest in the development of wood-derived graphene materials and their nanodevices.

Modular 'click-in-emulsion' bone-targeted nanogels.

A new class of nanogel demonstrates modular biodistribution and affinity for bone. Nanogels, ∼70 nm in diameter and synthesized via an astoichiometric click-chemistry in-emulsion method, controllably display residual, free clickable functional groups. Functionalization with a bisphosphonate ligand results in significant binding to bone on the inner walls of marrow cavities, liver avoidance, and anti-osteoporotic effects.